A power cut, fire alarm activation or damaged circuit can turn an ordinary corridor, stairwell or warehouse exit into a serious safety risk within seconds. Knowing how to test emergency lighting gives the responsible person confidence that escape routes will remain visible when normal lighting fails – and provides a clear record that the system is being maintained properly.

Emergency lighting is not a fit-and-forget installation. Batteries degrade, lamps fail, chargers develop faults and changes to a building can leave parts of an escape route poorly covered. Regular checks identify those issues before an emergency exposes them.

What emergency lighting testing involves

Emergency lighting is designed to operate when the normal lighting supply fails. It may be non-maintained, meaning fittings only illuminate during a mains failure, or maintained, where fittings stay illuminated as part of the normal lighting scheme and continue to operate on battery power if the supply is lost. Many premises have a mixture of both.

Testing usually falls into three areas: routine visual checks, monthly functional tests and an annual full-duration test. The exact arrangement should reflect the system installed, the manufacturer’s instructions, the building’s fire risk assessment and the relevant British Standards, including BS 5266 guidance.

For most UK businesses, the Regulatory Reform (Fire Safety) Order 2005 requires the responsible person to ensure fire safety equipment is maintained in an efficient state, in efficient working order and in good repair. It does not mean every building follows an identical checklist. A small office, a busy care setting, a warehouse operating night shifts and a block of flats all have different risks and practical constraints.

Who should test emergency lighting?

A designated responsible person can carry out straightforward routine checks if they understand the system, have been shown the correct test method and can recognise a fault. This is often a facilities manager, caretaker, site manager or trained member of staff.

However, annual testing, fault diagnosis, battery replacement, repairs and any work on fixed wiring should be handled by a competent electrical contractor. This is particularly important in larger commercial or industrial premises, where emergency lighting may be connected to central battery systems, automatic test equipment or fire safety controls.

The person carrying out checks should also know when not to test. If there is an active fire alarm, an evacuation, essential night work or another situation where emergency coverage is needed, postpone the test and record the reason.

Before you test the system

Start by checking the emergency lighting logbook. It should show the location of fittings, previous faults, dates of tests, remedial work completed and the rated duration of the system. Most standalone emergency fittings are rated for either one or three hours, but the rating must be confirmed from the fitting label, installation information or previous certification.

Tell relevant staff before testing, particularly reception teams, security, building users and any contractor working alone. A test can cause normal lighting circuits to switch off or emergency fittings to illuminate, which may otherwise be mistaken for a fault or power cut.

It is also good practice to carry out testing at a time when reduced lighting will not create a hazard. In a warehouse, for example, do not test a route used by forklift lorries. In offices, ensure staircases and corridors can still be used safely. If necessary, test areas in sections and arrange temporary controls.

Avoid switching off a distribution board or isolating a whole circuit simply to see what happens unless this has been planned and assessed. That approach can interrupt equipment, security systems, IT infrastructure or other essential building services. A dedicated emergency-lighting test key switch is normally the safer and more controlled method.

How to test emergency lighting each month

A monthly functional test confirms that each fitting transfers to battery operation when the normal supply is removed. It is a short test, not a full battery discharge.

Use the designated test key switch for the relevant emergency lighting circuit. Turn the key to simulate a mains failure, then check that the emergency fittings illuminate. Walk the escape routes rather than checking only the first fitting you can see. Look at corridors, stairwells, changes in level, final exits, fire alarm call points, fire-fighting equipment and externally illuminated escape routes where provided.

You are checking more than whether a lamp is on. The light needs to be bright enough to make the route usable, and the fitting, diffuser and signage should be undamaged and clean. A discoloured diffuser, flickering LED, loose fitting or obscured exit sign should be recorded as a defect.

After a short period, return the test key to its normal position and confirm the charge indicator returns to normal. Green LEDs are common, but the meaning of indicator lights varies by manufacturer. A green light does not always prove that the battery will support the fitting for its full rated duration, which is why the annual discharge test still matters.

Record the date, areas checked, result and any faults in the logbook. If a fitting fails to illuminate, label it where appropriate, raise the repair promptly and consider whether interim measures are needed. A failed fitting on a critical escape route should not be left until the next planned visit.

Carrying out the annual duration test

The annual test is the more demanding check. It verifies that the emergency lighting can operate for its full rated duration, commonly one or three hours. The test should be planned carefully because the system will be discharged and may need up to 24 hours, or the period specified by the manufacturer, to fully recharge afterwards.

Operate the designated test facility and leave the emergency lights running for the full required period. At the end of the test, inspect each fitting and exit sign. They should remain illuminated and provide suitable coverage across the escape route. A fitting that works for the first few minutes but fades or fails before the end of the test has not passed.

Where a full-duration test would leave a building without adequate emergency cover during occupied hours, schedule it when the premises are closed or when alternative safety arrangements are in place. Some sites need a staged test programme so that not every area is left with discharged batteries at once. This decision should align with the fire risk assessment, not simply convenience.

Once mains power is restored, check that fittings return to charge mode and note the recharge period in the logbook. Any battery or fitting failures should be repaired without delay, followed by a suitable retest.

Keep an emergency lighting logbook

A clear logbook makes compliance easier to demonstrate and helps prevent repeat faults being overlooked. It can be paper-based or digital, provided it is accessible and kept up to date.

Each entry should identify the test date, type of test, person carrying it out, areas or fittings checked, results, defects found and corrective action taken. Retain inspection reports, repair records and certificates with the logbook. For larger sites, an up-to-date emergency lighting plan is also useful, especially where fittings are numbered.

Good records are valuable during fire risk assessments, insurance reviews, audits and investigations. More importantly, they show whether a recurring fault is being properly resolved rather than repeatedly noted and ignored.

Common emergency lighting faults to look for

Battery failure is one of the most common problems. Emergency lighting batteries have a limited service life, and a fitting may appear normal until a duration test exposes a weakened battery. Damaged charging circuits, failed LED boards and incorrect replacement batteries can produce similar symptoms.

Building alterations also cause issues. Partition walls, new racking, changed room layouts and relocated doors can alter the escape route or block light that previously covered it. A lighting scheme that was suitable at installation may no longer provide adequate illumination where people now need to travel.

Watch for missing test keys, labels that no longer match circuits, fittings painted over during refurbishment, exit legends that are difficult to read and fittings installed in areas where they are regularly knocked or contaminated. These are practical defects, but each can matter in an evacuation.

When to call a qualified electrician

Call a competent contractor if emergency fittings fail their monthly or annual test, batteries require replacement, the test switch does not operate correctly or there is uncertainty about what system is installed. Professional support is also sensible after a change of use, extension, refurbishment or revised fire risk assessment.

An electrician can test the installation, identify circuit faults, replace unsuitable or obsolete fittings and assess whether the coverage still meets the needs of the building. For commercial and industrial sites, FCR Electrical can provide organised emergency lighting testing, remedial work and compliant electrical support with minimal disruption to operations.

Treat emergency lighting checks as part of everyday building safety, not a task to rush through at the end of the month. A well-maintained system gives people a clearer route out when they need it most.